Alloy Tail Tidy / Rear Fender Eliminator Kit for Street Scrambler, Street Twin, Street Cup (2016-2022) and Speed Twin 900 (2023-2024)

Easy fit plug and play wiring. Strong and well made. Lights are great quality too. Something to consider is the mounting holes for the number plate are high up bringing the screws near the edge of the number plate. Also a standard size plate doesn't fit between the indicators. Luckily I have a smaller plate.

Would have 5 stars but wires too short to reach indicators and nuts missing to attach tail light.

Bike looks completely different and really tidied up the rear end. Finished it off with the flare indicators and it’s perfect.

I was unsure whether to go for a shorter tail. After emailing Tec and ordering the Tidy Tail and Fuze indicators, the bike looks so much better! The rear now feels much less "bulky" visually. Easy and quick to install thanks to the plug n play and clear instructions. Thanks, Tec!

Le kit s’intègre parfaitement à la moto

Tail tidy looks great & simple to fit. May get some tec indicators,not really happy with mine now. You will get crap on your back end when it's wet but just stays short of your jacket.

Fits great , looks great

Great product, great price and very simple to fit 5⭐

Makes a real difference to the look of the bike. Much cleaner back end especially when combined with TEC’s LED indicators. I had to get longer bolts for the back holes and use the bolts for the back holes in the front holes to make it fit my 2021 street scrambler but other than that all very good. Although messaged TEC about the issue in case I was installing incorrectly and three days later still no response. Bit disappointing.

Excellent work on the design of this item fitted very well on the bike.

Ordered fuel booster plug, air filter and centre stand. All came quickly and fitted as expected. Will definitely buy from this company again.

Great tail tidy easy to fit,cleans up the back end, well worth getting one at a good price

Very nice and well made tidy, makes the bike look ten times better! Well made, feels sturdy, no complaints on overall quality and presentation, would recommend. My install however didn't go all that smoothly, some probably my fault, but there are a few things to consider before purchasing to make your life easier. • If you have stock Triumph (LED in my case) indicators, make sure you buy this with the 2 Hole OEM mounts. • Again if you have stock Triumph indicators with the white molex connectors, buy yourself some 2.4mm straight bullet terminals (Ebay) so you can press fit into the molex and don't have to cut anything off (I wanted the option to go back to stock). • Also again if you have the Triumph LED indicators, you will have to lengthen the wire as the loom is quite short. I used some standard bullet terminals, make sure you have this ready to go for install. • The instructions refer to the "front" and "back" of the unit, which is actually the unit itself not when on the bike. So the front is actually the rear where the lights and plate are. Use the long bolts/spacers on the end closest to the front of your bike and the shorter bolts/spacers on the tail light end. Still giving 5 stars as it's unfair to expect a "one size fits every possible configuration", but ideally it could be clearer that extra work is necessary to fit the unit, especially with stock indicators. Supplied instructions could also do with an update just to make it clear which end is the "front", but this might just be me.

Easier to fit than I thought just the issue of switching red n black wires which is mentioned in the instruction leaflet. Good quality piece of kit and slug indicators complete a neater look on my Street Cup.

I haven’t fitted it yet but the quality is second to none. 👍🏻well done TEC.

The bike looks awesome with it on! The large under tray is a huge seller for me but still took extra precaution protecting the wiring. The rear light does come with a downward facing light strip that - despite being red - points enough light on to the number plate. MOT guy confirmed. Be warned though, not all will agree. Scrambler folks take note: due to the new location of your plate, it’s highly likely that your rear tire will make contact with the number plate if you ride it like you stole it over speed bumps, especially with with knobbly tires.

Looks Great! Rear long bolts were too short for my Street Twin - easy fix to use other bolts. Slight vibration at a certain rev range - but minimal. Overall a great product and very good value. The light really does need to have a clear window at the bottom for the number plate - this will be an issue here in NZ.

Brilliant bit of kit which makes the back end of the bike so much tidier. Good instructions for fitting and half the price of a Triumph unit. I am hoping that it will get through the MOT okay with the LED with the Lucas type rear light as it doesn't have a dedicated number plate clear light.

생각했던 그림대로 장착. 아주 마음에 듭니다. 제품 퀄리티도 좋구요...다만 동봉되어있는 볼트 길이가 짧아서 장착하는데 아주 살짝 애먹었네요.... 차대에 고정하는 볼트가 짧은거 2개, 긴거 2개던데...4개모두 긴걸로 해야 쉽게 장착 가능할 듯 합니다!!

Speedy delivery to Spain, good product, couple of mounting holes seemed a bit off, easily re drilled as is aluminium. Also, says is EU legal, but has no dedicated number plate light, which is legal requirement here in Spain. I drilled some holes in bottom of lens and covered with clear plastic, so all good now.

Well made and mechanically straight forward to fit wiring not perfect but not a major problem, all in all it is a big improvement to the back end , no number plate light on Lucas style tail light so that will need doing before next MOT good service from Tec as usual.

Bob on no probs at all bike starting to look like it should

easy to fit, nice quality and the loom means no modifying the original wiring, although the tail light blue and red wires needed swapping over as the brake light was permanently on. Also there is no licence plate light incorporated into the lucas tail light which may bother some people but I am told this is not a MOT requirement. I recommend fitting with the TEC bullet indicators to complete the look plus you can leave the stock indicators on the original fender for quick change back if required. you won't need the resistors for LC triumphs as you can alter the flash rate on the dash ( even if you have a combination of led and stock ) you tube will show you how to change the flash rate on the dash. I give 4 stars only because of the wiring error on the loom.

Good quality part and a perfect fit for my street twin.Did have a problem with the connect block that came with the tail light it wouldn’t power the indicators . I used the original block and connector and solder the rear light into the original wires

Very prompt delivery, easy to read and understand instructions and really good quality. In general its really good and definitely improves the look of the bike. Couple of minor comments that if they could be resolved would make it even better. *I retained the stock indicators which have very short wires. Using the connectors provided in the package I soldered up extensions to reach the wires provided. However the connectors at the indicator ends are left half in half out of the tail tidy and are not neat. See Pic *The rubber gasket is not easy to "fit" I glued it to the Light to make sure before fitting. A one piece covering the whole of the back of the light with holes for the fixing bolts would locate it perfectly. * The number plate taken off the original fitting did not fit onto the new one. I had to drill new holes 1/3 inch higher up the plate to get it fitted under the light. See Pic

Once again great quality products and speedy delivery. I did have some questions and their response was fast and knowledgable, I also returned some products that I didn’t need, they refunded me straight away. Quality company to deal with. Many thanks!!!

Good product which was easy to fit.

Quite easy to fit mechanically. Spent some more time to get the wiring and resistors right and tidy. Follow the instructions and mount the rear light before fitting the tail tidy.

Easy to fit physically and looks great. I did have issues with the supplied loom, make sure you have a circuit tester and check out the feeds before you close up, for mine, the earth was incorrect and needed a change over.

This has made such a difference to the look of my street scrambler!!! Took a little longer to fit than I’d expected, but still worth the time an money !!!! Great value in my eyes! An would highly recommend.. Thanks Tec for your excellent service 👌

My bike was totally transformed by putting this tail tidy on would highly recommend tec as all parts I've ordered have fitted perfectly and are very good quality

Fantastic service! Next day delivery for me up in Scotland. When the part arrived it was very well packaged. Everything has been thought of. Fitting instructions included as well as a comprehensive list of other parts available for your model of bike which I felt was a really nice touch. Fitting the tail tidy itself was pain free. Everything lined up and the engineering of the part itself is great! Feels and looks very well made. All fitting bolts/spacers were included and wiring instructions were easy to follow. It really sets off the street scrambler and changes how the bike looks completely. All of that for a very affordavle price! Will definitely be using TEC again in the future.

Fits great looks good could do with cable extensions for indicators

Very good quality product very helpful prompt delivery and response.cheers

Must have ataken a kilo or two off the weight and looks great.

Makes the back end much neater, I was originally going to use the o/e indicators, but it really doesn’t look right, best to get something smaller.

Great service! Good quality products.

Easy to fit and looks brilliant No plug and play harness so wiring a bit fiddly

Buen producto, bien terminado, fácil instalación, queda muy bonito. Para futuras compras desde España sería conveniente que hablaran español.

Very well made part , easy to fit and fastly delivered! Competitive price on top of all of that...

Looks cracking and great value. Just a couple of minor quibbles. Bit of a tight fit for the bench seat on the Street Twin, but the seat goes on with a good old fashioned push. The wiring from the tail light for the indicators is coloured opposite to the instructions, so had to swap them round, and the loom wiring is too short so had to twist some extra links in. Looks good with the rack too.